Reading the Sequence on a Peptide Certificate: Ends, Salts and Net Content
Free acid or amide, acetylated or not, salt or free peptide: how the ends of a sequence change the molecule, and which mass on a certificate to check.
Published 17 November 2026
Two vials can carry the same name and contain different molecules. Most of the time the difference is not in the middle of the sequence but at its two ends, where small chemical caps change the mass, the behaviour on a column and the way the compound is described. This page explains how to read the ends of a sequence on a certificate, why salts make the vial weight misleading, and which single number settles identity.
Identity comes before purity#
The first question about any peptide is not how pure it is but whether it is the molecule named on the label. A purity figure from HPLC describes the sample as it separated on the column: the share of the detector signal under the main peak. It says nothing about what that main peak is. Identity is a separate measurement, usually mass spectrometry, and a certificate should report both. If there is a purity percentage and no mass, half the question has not been answered.
The ends of the chain change the molecule#
Every linear peptide has two ends. The start, the N-terminus, carries a free amino group unless something has been added to it. The finish, the C-terminus, is either a free acid or, very often, an amide. Certificates and catalogues show this with a short notation:
- H- at the start: a free N-terminus, nothing added.
- Ac- at the start: an acetyl group on the N-terminus.
- -OH at the end: a free acid.
- -NH2 at the end: a C-terminal amide.
Each of these is a different compound with its own mass. An acetyl group adds about 42 daltons. Turning a free acid into an amide takes away about one. Neither change shows up in a short product name, which is how two vials sold under the same name can hold different things.
A worked example#
Semax is a seven-residue peptide, Met-Glu-His-Phe-Pro-Gly-Pro, with a free N-terminus and a free acid at the end. Its molecular weight is about 813.9. Some catalogues also list "N-acetyl Semax amidate": the same seven residues, with an acetyl group added at the start and an amide at the end. That molecule weighs about 855.
Selank shows the same pattern. Thr-Lys-Pro-Arg-Pro-Gly-Pro weighs about 751.9; the N-acetylated amide version is about 793.
So the name on the label tells you the family. The sequence written out with its ends, and a mass that matches it, tells you the molecule. If a certificate gives the name but not the sequence with its terminal notation, ask which form was analysed. The same check applies to any peptide where both forms are sold; our posts on Kisspeptin-10 and KPV walk through it for an amide and an acid.
Salts, and why the vial weight is not the peptide weight#
Peptides are rarely supplied as the bare molecule. Freeze-dried material carries water, and peptides with basic residues (lysine, arginine, a free N-terminus) are usually made as a salt, most often acetate or trifluoroacetate. The counter-ion is part of the powder's weight but not part of the peptide.
That is why two numbers on a certificate can both be right and still disagree:
- Molecular weight of the free peptide: the number that identity is checked against.
- Net peptide content: the share of the powder, by mass, that is actually peptide. On many short peptides it sits somewhere between about 70 and 95 per cent.
A sample can be 99% pure by HPLC and still be only 80% peptide by mass, because the rest is salt and water that the purity method was never measuring. Our post on purity testing versus quantification and the guide on how much is in the vial go into this in more detail.
What a purity figure does not tell you#
A purity percentage is relative. It compares the main peak with everything else the detector saw, under one method. It does not say how much peptide is in the vial, whether the main peak is the right sequence, or which salt form you have. Read it as one line among several, never as the whole certificate. See what an HPLC purity figure means for how the number is produced.
A short list to work through#
Before relying on a certificate, it is worth being able to answer each of these from the document itself:
- Is the full sequence written out, including the notation at both ends?
- Is there a mass, and does it match that exact sequence, with its ends?
- Does it say whether the figure is for the free peptide or a salt?
- Is net peptide content reported, or only HPLC purity?
- Does it name the laboratory, the method and the batch, and is that the batch you were sent?
Our guides on how to read a certificate of analysis and how to verify a certificate is genuine cover the last point. At Pioneer, a batch certificate is available on request: ask which form, which salt and which batch it describes before you order.
For laboratory research use only. Not for human or veterinary use.
Pioneer Research Peptides — UK supplier of research peptides for laboratory use. Ask about batch documentation before you order.
For laboratory research use only — not for human consumption. 18+.
Research peptides from UK stock#
Supplied for laboratory research use only. Ask about the documentation for a batch before you order.
